Description
Sheet size: A4
Custom Printed Design
Please note as this is custom printed it falls outside of our same day dispatch service as minimum of 12hrs is required for the print to dry to prevent shrinkage, these items will be dispatched the next working day.
***Special Note*** Please allow for slight colour variations between pictures and actual products. Computer monitors may display colour differently. If you have any concerns, please contact us before purchasing.
An Application Tape is required for this product, we sell a number of application tapes all can be reused and have carriers on the back, just replace after each use to get the most from each piece
- For HTV use : TTD Easy MASK
- For SA use: Application Tape
Media should be loaded in your machine with the printed side uppermost.
DO NOT MIRROR YOUR DESIGN
HTV Cutting Settings
Cricut: | Silhouette Cameo: | Scan N Cut: |
Blade: Standard Setting: Iron On |
Blade: Standard, 3 Material: Heat Transfer, Smooth Speed: 8 Force: 6 |
Blade: Standard, 2 Cut Speed: 1 Cut Pressure: 1 |
Roland GS/GX-24: | Graphtec: | MH, SC2, LP3, and Titan 1: | Titan 2 & 3: |
Blade: 45° Gram Force: 80-90 Offset: .250 Speed: 25-50 cm/s |
Blade: 45° Gram Force: 9 Tool: CB09U+0 Speed: 25 cm/s |
Blade: 45°/60° Gram Force: 80-85 Speed: 300mm/s *Blade Advancing Varies |
Blade: 45°/60° Gram Force: 60-65 Speed: 300mm/s *Blade Advancing Varies |
Self Adhesive Cutting Settings
Cricut: | Silhouette Cameo: | Scan N Cut: |
Blade: Standard Setting: Vinyl |
Blade: Standard, 2-3 Material: Vinyl Speed: 7 Force: 5 |
Blade: Standard, 2 Cut Speed: 1 Cut Pressure: 2 |
Roland GS/GX-24: | Graphtec: | MH, SC2, LP3, and Titan 1: | Titan 2 & 3: |
Blade: 45° Gram Force: 80-90 Offset: .250 Speed: 25-50 cm/s |
Blade: 45° Gram Force: 9 Tool: CB09U+0 Speed: 25 cm/s |
Blade: 45°/60° Gram Force: 80-85 Speed: 300mm/s *Blade Advancing Varies |
Blade: 45°/60° Gram Force: 60-65 Speed: 300mm/s *Blade Advancing Varies |
Settings may vary based on blade condition and age of machine. Always perform a test cut prior to cutting designs.
HTV Application Instructions
A sheet of TTD EASY MASK will be required to transfer your design to your garment. (these are reusable and can be purchased separately)
Applies To:
• 100% cotton
• Poly/cotton blends
• 100% polyester
• Leather
• Lycra®/spandex
Application instructions (home iron) DO NOT USE STEAM • Set iron dial between Cotton and Linen • Cover design with Kraft paper or non-stick cover sheet • Place on flat, hard surface (ironing board not recommended) • Press iron with medium/firm pressure (do not slide iron) • Press each section of design for 15 seconds • If areas of design lift after application, replace cover sheet and re-press for 10 seconds • Peel carrier hot or cold |
Application Instructions (heat press) • Weed excess material • Mask with TTD High Tack Mask • Preheat garment for 2-3 seconds • Apply design at 305°F/150°C • Use medium pressure for 10-15 seconds • Peel carrier hot or cold • Cover and reheat for 2-3 seconds |
Self Adhesive Application Instructions
Cut Design (DO NOT REVERSE)
Apply transfer tape
Apply to item
Allow 24 Hours before washing
HTV
Laundering:
• Wait 24 hours before 1st wash
• Machine wash cold / mild detergent
• Dry on normal dryer setting
• Do not dry clean or bleach
Self Adhesive
Washing:
• Wait 24 hours before 1st wash
• Hand wash only with mild detergent
• Dry without hard rubbing
• Do not wash in Dishwasher
The product is REACH compliant
The product is certified VeganOK
Products compliant with the VEGANOK Ethical Regulations are recognizable as they
ALWAYS carry the VEGANOK trademark