StripFlock® Pro Heat Transfer Vinyl
StripFlock® Pro Heat Transfer Vinyl
The Only Flock in the Industry that can be Layered On Itself.
A great alternative to embroidery, StripFlock Pro heat transfer vinyl gives logos a raised, textured, suede-like feel. The deep, opaque colors make StripFlock Pro excellent for retro designs or anytime you want a rich look. StripFlock Pro looks excellent on caps, bags, and garments that need textured visual interest. Use Stripflock Pro as a base layer and cover with other materials or more StripFlock! The ability to layer this material allows you to say “yes” to multi-color designs.
StripFlock Pro is CPSIA Certified so you can decorate kids’ items with confidence.
***Special Note*** Please allow for slight colour variations between pictures and actual products. Computer monitors may display colour differently. If you have any concerns, please contact us before purchasing.
Media should be loaded in your machine with the dull side uppermost.
MIRROR YOUR DESIGN
HTV Cutting Settings
Cricut: |
Silhouette Cameo: |
Scan N Cut: |
Blade: Standard
Setting: Iron On |
Blade: Standard, 3
Material: Heat Transfer, Smooth
Speed: 8
Force: 6 |
Blade: Standard, 2
Cut Speed: 1
Cut Pressure: 1 |
Roland GS/GX-24: |
Graphtec: |
MH, SC2, LP3, and Titan 1: |
Titan 2 & 3: |
Blade: 45°
Gram Force: 80-90
Offset: .250
Speed: 25-50 cm/s |
Blade: 45°
Gram Force: 9
Tool: CB09U+0
Speed: 25 cm/s |
Blade: 45°/60°
Gram Force: 80-85
Speed: 300mm/s
*Blade Advancing Varies |
Blade: 45°/60°
Gram Force: 60-65
Speed: 300mm/s
*Blade Advancing Varies |
Self Adhesive Cutting Settings
Cricut: |
Silhouette Cameo: |
Scan N Cut: |
Blade: Standard
Setting: Vinyl |
Blade: Standard, 2-3
Material: Vinyl
Speed: 7
Force: 5 |
Blade: Standard, 2
Cut Speed: 1
Cut Pressure: 2 |
Roland GS/GX-24: |
Graphtec: |
MH, SC2, LP3, and Titan 1: |
Titan 2 & 3: |
Blade: 45°
Gram Force: 80-90
Offset: .250
Speed: 25-50 cm/s |
Blade: 45°
Gram Force: 9
Tool: CB09U+0
Speed: 25 cm/s |
Blade: 45°/60°
Gram Force: 80-85
Speed: 300mm/s
*Blade Advancing Varies |
Blade: 45°/60°
Gram Force: 60-65
Speed: 300mm/s
*Blade Advancing Varies |
Settings may vary based on blade condition and age of machine. Always perform a test cut prior to cutting designs.
Stripflock® Pro Application Instructions
Applies To:
• 100% cotton
• Poly/cotton blends
• 100% polyester
Application instructions (home iron)
DO NOT USE STEAM
• Set iron dial between Cotton and Linen
• Cover design with Kraft paper or non-stick cover sheet
• Place on flat, hard surface (ironing board not recommended)
• Press iron with medium/firm pressure (do not slide iron)
• Press each section of design for 15 seconds
• If areas of design lift after application, replace cover sheet
and re-press for 10 seconds
• Peel carrier hot or cold |
Application Instructions (heat press)
• Weed excess material
• Preheat garment for 2-3 seconds
• Apply design at 305°F/150°C
• Use medium pressure for 10-15 seconds
• Peel carrier hot or cold
• Cover and reheat for 2-3 seconds |
Laundering:
• Wait 24 hours before 1st wash
• Machine wash cold / mild detergent
• Dry on normal dryer setting
• Do not dry clean or bleach